aboutsummaryrefslogtreecommitdiff
path: root/nx-X11/config/cf/host.def.NX.original
diff options
context:
space:
mode:
Diffstat (limited to 'nx-X11/config/cf/host.def.NX.original')
-rw-r--r--nx-X11/config/cf/host.def.NX.original1020
1 files changed, 1020 insertions, 0 deletions
diff --git a/nx-X11/config/cf/host.def.NX.original b/nx-X11/config/cf/host.def.NX.original
new file mode 100644
index 000000000..a201cfa9c
--- /dev/null
+++ b/nx-X11/config/cf/host.def.NX.original
@@ -0,0 +1,1020 @@
+XCOMM $XFree86: xc/config/cf/xf86site.def,v 3.186 2003/06/25 18:06:22 eich Exp $
+/******************************************************************************/
+/*
+ * This file is to provide a quick method for most people to change the
+ * behaviour of their Xorg installation without having to fully
+ * understand the workings of site.def and all the various '.cf' files.
+ *
+ * In the vast majority of cases, it should not be necessary to use this
+ * file at all or change it in any way.
+ *
+ * This file is divided into two sections. The first contains settings
+ * that end-users might reasonably change. The second contains settings
+ * that developers might want to change.
+ *
+ * IMPORTANT NOTE: In all cases changing the defaults may cause problems
+ * and/or unexpected side-effects. If you don't understand what a setting
+ * does, then it's best to not change it. If you make changes and have
+ * problems, verify that those problems are also present when using an
+ * empty host.def file and unchanged version of this file before reporting
+ * them.
+ *
+ * A good way to use this file is to copy it to host.def, and make the
+ * changes there. That way, future patches to this file won't fail.
+ * The host.def file will never be patched.
+ *
+ * The distributed version of this file MUST contain no uncommented
+ * definitions. Default definitions belong in xorg.cf, or <vendor>.cf
+ * files.
+ */
+/******************************************************************************/
+
+/**************************************************************************/
+/* */
+/* Copyright (c) 2001, 2007 NoMachine, http://www.nomachine.com/. */
+/* */
+/* NX-X11, NX protocol compression and NX extensions to this software */
+/* are copyright of NoMachine. Redistribution and use of the present */
+/* software is allowed according to terms specified in the file LICENSE */
+/* which comes in the source distribution. */
+/* */
+/* Check http://www.nomachine.com/licensing.html for applicability. */
+/* */
+/* NX and NoMachine are trademarks of NoMachine S.r.l. */
+/* */
+/* All rights reserved. */
+/* */
+/**************************************************************************/
+
+#if !defined(NXZaurusXServer) && !defined(NXiPAQXServer) && !defined(DarwinArchitecture)
+
+#if defined(SunArchitecture)
+#define ProjectRoot /usr/openwin
+#endif
+
+/*
+ * Enable use the Cygwin IPC libraries to get MIT-SHM support.
+ */
+#if defined(cygwinArchitecture)
+#define UseCygIPC YES
+#endif
+
+/*
+ * If you have build-specific modifications in your host.def file, but
+ * want an empty host.def file installed when doing 'make install',
+ * uncomment the following
+ *
+#define InstallEmptyHostDef
+ */
+
+/*
+ * Which servers to build. There is only Xorg server.
+ * It can be disabled by the following.
+ *
+#define XorgServer NO
+ */
+#define XorgServer NO
+
+/*
+ * To disable building the Xnest server, uncomment this.
+ *
+#define XnestServer NO
+ */
+#define XnestServer NO
+
+/*
+ * To disable building Xvfb, uncomment this.
+ *
+#define XVirtualFramebufferServer NO
+ */
+#define XVirtualFramebufferServer NO
+
+/*
+ * To enable building Xdmx, uncomment this.
+ *
+#define XdmxServer YES
+ */
+#define XdmxServer NO
+
+/*
+ * To disable building Xprt, uncomment this.
+ *
+#define XprtServer NO
+ */
+#define XprtServer NO
+
+/*
+ * Xprint is needed by Xprt. You can disable it if
+ * you are not going to build Xprt.
+ *
+#define BuildXprint NO
+ */
+#define BuildXprint NO
+
+/*
+ * Building libraries with NX enhancements is disabled
+ * by default. You should enable this in your host.def.
+ *
+#define NXLibraries YES
+ */
+#define NXLibraries YES
+
+/*
+ * Building the NX agent nested server is disabled
+ * by default. Enable this in your host.def.
+ *
+#define NXAgentServer YES
+ */
+#define NXAgentServer YES
+
+/*
+ * Assume the new build tree.
+ *
+#define NXUpgradeAgentServer NO
+ */
+#define NXUpgradeAgentServer YES
+
+#ifdef NXAgentServer
+#define BuildRenderLibrary YES
+#define SharedLibFreetype2 YES
+#define NormalLibFreetype2 YES
+#define FontLibSharedFreeType NO
+#endif
+
+/*
+ * Define this symbol to build the NX enhanced MS Windows
+ * X server for Cygnus environment.
+ *
+#define NXWinServer YES
+ */
+#if defined(cygwinArchitecture)
+#define NXWinServer NO
+#define XWinServer NO
+#endif
+
+/*
+ * Set the default server (ie the one that gets the sym-link to "X")
+ *
+#define ServerToInstall Xorg
+ */
+
+/*
+ * Force build of X libraries if any nested server is to be built.
+ *
+#define BuildLibraries YES
+ *
+ * If you just want libraries for NXAgentServer, this should be
+ * enough (never tested, although).
+ *
+#define BuildLibrariesForXServers YES
+ */
+#if XnestServer || NXAgentServer
+#define BuildLibraries YES
+#endif
+
+#define BuildDamageLibrary YES
+
+#define BuildXfixesLibrary YES
+
+#define BuildCompositeLibrary YES
+
+#define BuildRandRLibrary YES
+
+#define BuildDocs NO
+
+#define BuildComposite YES
+
+/*
+ * If you only run the X server under xdm the X servers don't need to be
+ * installed SetUID, and you may comment out the lines below. If you run
+ * the servers by hand (with xinit or startx), then they do need to be
+ * installed SetUID on most platforms.
+ *
+ * Consult your system administrator before making the X server setuid.
+ *
+#define InstallXserverSetUID NO
+ */
+
+
+/*
+ * Server configuration parameters. The defaults are shown here:
+ */
+
+/*
+ * Which drivers to build. When building a static server, each of these
+ * will be included in it. When building the loadable server each of these
+ * modules will be built.
+ *
+#define XF86CardDrivers mga glint nv tga s3virge sis rendition \
+ neomagic i740 tdfx savage \
+ cirrus vmware tseng trident chips apm \
+ GlideDriver fbdev i128 \
+ ati DevelDrivers ark cyrix \
+ siliconmotion \
+ vesa vga XF86OSCardDrivers XF86ExtraCardDrivers
+ */
+
+/*
+ * To add third party drivers to the standard driver list, set the
+ * following.
+ *
+#define XF86ExtraCardDrivers extradriver1 extradriver2 ...
+ */
+
+/*
+ * Select the XInput devices you want by uncommenting this.
+ *
+#define XInputDrivers mouse keyboard acecad calcomp citron \
+ digitaledge dmc dynapro elographics \
+ microtouch mutouch penmount spaceorb summa \
+ wacom void magictouch aiptek
+ */
+
+/* To enable building of development DRI drivers (insecure, or not
+ * useful on the chosen architecture, uncomment this define.
+#define BuildDevelDRIDrivers YES
+ */
+
+/*
+ * To use the deprecated, old keyboard driver, uncomment this. But
+ * even better, make the new keyboard driver (hw/xfree86/input/keyboard)
+ * work for your architechture. The old driver will be removed in the
+ * next release.
+ *
+#define UseDeprecatedKeyboardDriver YES
+ */
+
+/*
+ * There are three parameters that determine where and how the Matrox HAL
+ * library is used:
+ *
+ * HaveMatroxHal -- You have the HALlib.a binary library installed
+ * in xfree86/drivers/mga/HALlib, and you want it to
+ * be used.
+ * Default: NO
+ *
+ * BuildMatroxHal -- You have the source for the HALlib library (installed
+ * in xfree86/drivers/mga/hallib), and want to build and
+ * use it.
+ * Default: NO
+ *
+ * UseMatroxHal -- You want to build support for loading/using the HAL
+ * library into the mga driver. For module server builds
+ * you don't need to have the HALlib library to do this.
+ * but you want to build support for loading it and using
+ * it into the mga driver module.
+ * Default: YES for loadable server build
+ * (HaveMatroxHal || BuildMatroxHal) for static
+ */
+
+/*
+ * To disable use of the Matrox HAL library, uncomment this:
+ *
+#define UseMatroxHal NO
+ */
+
+/*
+ * If you have the HALlib.a binary installed in xfree86/drivers/mga/HALlib,
+ * uncomment this:
+ *
+#define HaveMatroxHal YES
+ */
+
+/*
+ * If you have the HALlib source code installed in xfree86/drivers/mga/hallib,
+ * uncomment this:
+#define BuildMatroxHal YES
+ */
+
+/*
+ * To disable building the font server, uncomment this.
+ *
+#define BuildFontServer NO
+ */
+#define BuildFontServer NO
+
+/*
+ * Speedo fonts have been disabled by default in this release.
+ * To re-enable support for Speedo fonts, uncomment this.
+ *
+#define BuildSpeedo YES
+ */
+
+/*
+ * To disable support for CID fonts, uncomment this.
+ *
+#define BuildCID NO
+ */
+
+/*
+ * To disable support for TrueType fonts, uncomment these.
+ *
+#define BuildFreeType NO
+ */
+
+/*
+ * To set non-default build options for the underlying FreeType libraries,
+ * add them here and uncomment.
+ *
+#define Freetype2BuildDefines -DFREETYPE_BUILD_DEFINES
+ */
+
+/*
+ * To build the FreeType libraries with the TrueType byte code interpreter
+ * enabled, uncomment this. Note that there are patent issues related to the
+ * TrueType byte code interpreter, and we only recommend you enabling this
+ * if you are sure that there are no legal impediments to you doing so. See
+ * <http://www.freetype.org/patents.html> for further information.
+ *
+#define Freetype2BuildDefines -DTT_CONFIG_OPTION_BYTECODE_INTERPRETER
+ */
+
+/*
+ * Do you want to Build Fonts (Usually you only want to build and install
+ * fonts once, if this is a first time install you will want to build the
+ * fonts)
+ *
+#define BuildFonts NO
+ */
+#define BuildFonts NO
+
+/*
+ * To not build/install the 75dpi fonts, uncomment the following
+ *
+#define Build75DpiFonts NO
+ */
+
+/*
+ * To not build/install the 100dpi fonts, uncomment the following
+ *
+#define Build100DpiFonts NO
+ */
+
+/*
+ * To build/install the Speedo fonts, uncomment the following
+ * (see setting above about Speedo support as well)
+ *
+#define BuildSpeedoFonts YES
+ */
+
+/*
+ * To not build/install the Type1 fonts, uncomment the following
+ *
+#define BuildType1Fonts NO
+ */
+
+/*
+ * To not build/install the CID fonts, uncomment the following
+ *
+#define BuildCIDFonts NO
+ */
+
+/*
+ * To not build/install the True Type fonts, uncomment the following
+ *
+#define BuildTrueTypeFonts NO
+ */
+
+/*
+ * To not build/install the Cyrillic fonts, uncomment the following
+ *
+#define BuildCyrillicFonts NO
+ */
+
+/*
+ * To not install the local font directory, uncomment the following
+ *
+#define MakeLocalFontDir NO
+ */
+
+/*
+ * Include True Type Fonts to default font path. It is safe to do
+ * this by default as NX intaller carries only misc and TTF in the
+ * basic set of fonts installed under Windows.
+ *
+#define DefaultFontPath $(FONTDIR)/misc/,$(FONTDIR)/Speedo/,$(FONTDIR)/Type1/,$(FONTDIR)/75dpi/,$(FONTDIR)/100dpi/
+ */
+
+#if defined(LinuxArchitecture) || defined(SunArchitecture) || defined(FreeBSDArchitecture)
+#define DefaultFontPath $(FONTDIR)/misc/,$(FONTDIR)/Speedo/,$(FONTDIR)/Type1/,$(FONTDIR)/75dpi/,$(FONTDIR)/100dpi/,$(FONTDIR)/TTF/
+#endif /* #if defined(LinuxArchitecture) || defined(SunArchitecture) */
+
+#if defined(cygwinArchitecture)
+#define DefaultFontPath /mnt/NX/fonts/base/,/mnt/NX/fonts/misc/,/mnt/NX/fonts/Speedo/,/mnt/NX/fonts/Type1/,/mnt/NX/fonts/75dpi/,/mnt/NX/fonts/100dpi/,/mnt/NX/fonts/TTF/
+#define DefaultRGBDatabase /mnt/NX/fonts/rgb
+#endif /* #if defined(cygwinArchitecture) */
+
+/*
+ * To build only the servers with a cut-down source tree, uncomment
+ * this.
+ *
+#define BuildServersOnly YES
+ */
+#define BuildServersOnly YES
+
+/*
+ * By default, the sample config files for xinit, xdm and xfs are installed
+ * only when there is no pre-existing version installed. Uncommenting the
+ * following lines will force the sample versions to be installed even if
+ * it means over-writing existing versions.
+ *
+#define InstallXinitConfig YES
+#define InstallXdmConfig YES
+#define InstallFSConfig YES
+ */
+
+/*
+ * By default the application defaults files are always installed.
+ * Uncommenting the the following will prevent exising application
+ * defaults files from being over-written.
+ *
+#define InstallAppDefFiles NO
+ */
+
+/*
+ * Undefine the following if you don't want to have config files and
+ * app-defaults installed in a separate directory (i.e. /etc/X11).
+ *
+#define UseSeparateConfDir NO
+ */
+
+/*
+ * To enable building the glide driver, you need to define
+ * HasGlide2 to YES and set the Glide2IncDir variable.
+ * HasGlide2 is per default NO.
+ *
+#define HasGlide2 YES
+ */
+
+/*
+ * Set the path to your Glide include files.
+ *
+#define Glide2IncDir /usr/include/glide
+ */
+
+/*
+ * Have glide 3?
+ *
+#define HasGlide3 YES
+ */
+
+/*
+ * Set the path to your Glide 3 include files.
+ *
+#define Glide3IncDir /usr/include/glide3
+ */
+
+
+
+/*
+ * Unless you're a developer you shouldn't need to change anything
+ * beyond this point.
+ */
+
+/*
+ * If you want to enable some developer settings, like more verbose
+ * compiler warnings, uncomment this.
+ *
+#define XFree86Devel YES
+*/
+
+/*
+ * If using GCC 2.x on a system where it isn't the default, uncomment
+ * the following
+ *
+ */
+#if defined(SunArchitecture)
+#define HasGcc2 YES
+#define HasGcc YES
+#endif
+
+/*
+ * The default optimisation flags for GCC 2.x. -fno-strength-reduce is
+ * here to work around a bug in -O2 for GCC 2.x on i386 platforms.
+ * If you are using a version that doesn't have this bug, you can
+ * uncomment the following line, and remove '-fno-strength-reduce'
+ * If you are building binaries for a 486, it may be beneficial to add
+ * -m486
+ *
+#define DefaultGcc2i386Opt -O2 -fno-strength-reduce
+ */
+
+#if defined (LinuxArchitecture)
+#define DefaultGcc2i386Opt -g -O3
+#endif
+
+/*
+ * Enable all the optimizations on AMD64.
+ */
+
+#define DefaultGcc2AMD64Opt -g -O3 GccAliasingArgs
+
+/*
+ * This allows the GCC warning flags to be set. The default is shown here.
+ *
+#define GccWarningOptions -Wall -Wpointer-arith -Wstrict-prototypes \
+ -Wmissing-prototypes -Wmissing-declarations \
+ -Wredundant-decls -Wnested-externs
+ */
+
+/*
+ * Sun Compiler stuff..
+ *
+#define HasSunC YES
+#define HasSunCplusplus YES
+#define CplusplusCompilerMajorVersion 5
+#define CplusplusCompilerMinorVersion 0
+#define CCompilerMajorVersion 5
+#define CCompilerMinorVersion 0
+ */
+
+/*
+ * Optimized Sun Compiler Build.
+ *
+#define DefaultCDebugFlags -xO4 -xtarget=pentium_pro
+#define OptimizedCDebugFlags -xO4 -xtarget=pentium_pro
+ */
+
+/*
+ * Debuggable Sun Compiler Build.
+ * Note: This builds _EVERYTHING_ as debuggable
+ *
+#define DefaultCDebugFlags -g -xs
+#define OptimizedCDebugFlags -g -xs
+ */
+
+/*
+ * For Linux, this should match the Binutils version you have. This example
+ * is for 2.6.0.7. See linux.cf for the default setting.
+ *
+ * This should automatically get set correctly by imake.
+ *
+#define LinuxBinUtilsMajorVersion 26
+ */
+
+/*
+ * For Linux, these should match the libc version you have. This example
+ * is for libc.5.4.x. See linux.cf for the default setting.
+ *
+ * This should automatically get set correctly by imake.
+ *
+#define LinuxCLibMajorVersion 5
+#define LinuxClibMinorVersion 4
+ */
+
+/*
+ * If you want to use the GNU malloc library, uncomment this
+ *
+#define UseGnuMalloc YES
+ */
+
+/*
+ * Set this to whatever is required to access the GNU malloc library.
+ * The default is '-lgmalloc' unless is specified in the OS's .cf file.
+ *
+#define GnuMallocLibrary -L/usr/local/lib -lgmalloc
+ */
+
+/*
+ * To enable the internal Xserver malloc, uncomment this
+ *
+#define UseInternalMalloc YES
+ */
+
+/*
+ * Some Linux releases don't have a libtermcap. In this case you may need
+ * to uncomment the following
+ *
+#define TermcapLibrary -lncurses
+ */
+
+/*
+ * Build a server that dynamically loads the modules by setting
+ * this to YES. This defaults to YES on most platforms. A static server
+ * can be built by setting this to NO.
+ *
+#define DoLoadableServer NO
+ */
+
+/*
+ * This release defaults to building dlopen() style modules instead of the
+ * previously standard loader modules.
+ *
+ * Uncomment the following to return to the XFree86 custom loader modules.
+ *
+#define MakeDllModules NO
+ */
+
+/*
+ * Build XAA. This can be disabled with:
+ *
+#define XF86XAA NO
+ */
+
+/*
+ * Build vgahw. This can be disabled with:
+ *
+#define XF86VgaHw NO
+ */
+
+/*
+ * Build xf1bpp. This can be disabled with:
+ *
+#define XF1Bpp NO
+ */
+
+/*
+ * Build xf4bpp. This can be disabled with:
+ *
+#define XF4Bpp NO
+ */
+
+
+/*
+ * BSD Console driver support (for FreeBSD and NetBSD).
+ *
+ * By default, support is included for pccons and pcvt for NetBSD, and
+ * pccons, syscons and pcvt for FreeBSD.
+ *
+ * To change the list of supported drivers, set the following parameter.
+ * Possible values are -DPCCONS_SUPPORT, -DSYSCONS_SUPPORT, -DPCVT_SUPPORT.
+ * The following example includes support for syscons and pcvt only.
+ *
+#define XFree86ConsoleDefines -DSYSCONS_SUPPORT -DPCVT_SUPPORT
+ */
+
+/*
+ * To link the X server with a dynamic version of the Xfont library,
+ * uncomment this.
+ *
+#define XserverStaticFontLib NO
+ */
+
+/*
+ * To enable binary compatibility with previous versions of the font
+ * encoding support, uncomment this.
+ *
+#define FontencCompatibility YES
+ */
+
+/*
+ * To disable building XInput support, uncomment this
+ *
+#define BuildXInputExt NO
+ */
+#if defined(SunArchitecture)
+#define BuildXInputExt YES
+#endif
+
+/*
+ * Uncomment this for joystick support.
+ *
+ * Note: Joystick support is broken, so don't enable this.
+ *
+#define JoystickSupport YES
+ */
+
+/*
+ * To disable the ScreenSaver Extension, uncomment this line.
+ *
+#define BuildScreenSaverExt NO
+ */
+#define BuildScreenSaverExt NO
+
+/*
+ * If you don't want to build Xinerama support, uncomment this.
+ *
+#define BuildXinerama NO
+ */
+#define BuildXinerama NO
+
+/*
+ * If you don't want to build support for the GLX extension, uncomment this.
+ *
+#define BuildGlxExt NO
+ */
+#define BuildGlxExt YES
+
+/*
+ * Taken from xorg.cf.
+ */
+
+#if defined(SparcArchitecture) \
+ || defined (Sparc64Architecture) \
+ || defined(ia64Architecture) \
+ || defined(s390xArchitecture) \
+ || defined(AMD64Architecture)
+#define GlxExtraDefines -D__GLX_ALIGN64
+#endif
+
+/*
+ * If you want to build the xf86rush extension, uncomment this line.
+ * This isn't recommended.
+ *
+#define BuildXF86RushExt YES
+ */
+#define BuildXF86RushExt NO
+
+/*
+ * If you want to build the client library for the xf86rush extension,
+ * uncomment this line. This isn't recommended.
+ *
+#define BuildXF86RushLibrary NO
+ */
+#define BuildXF86RushLibrary NO
+
+/*
+ * We should never need LBX in a NX enabled environment...
+ *
+#define BuildLBX NO
+ */
+#define BuildLBX NO
+
+#define BuildXKB YES
+#define BuildXKBlib YES
+
+#define SharedLibXau NO
+
+/*
+ * If you are running NetBSD 0.9C or later, and have the aperture driver
+ * installed, uncomment this.
+ *
+#define HasNetBSDApertureDriver YES
+ */
+
+/*
+ * If you are running SVR3 and have the mmap driver installed (for linear
+ * framebuffer access) uncomment this.
+ *
+#define HasSVR3mmapDrv YES
+ */
+
+/*
+ * If you are using an SVR3 (like ISC 4.x) which supports long file names,
+ * you can uncomment this to have manual pages installed under their
+ * full names
+ *
+#define ExpandManNames YES
+ */
+
+/*
+ * For a POSIXized build on Interactive uncomment this
+ * Could be used with gcc 'till Version 2.6.3
+ * Should be used with gcc 2.7.2.
+ *
+#define UsePosix YES
+ */
+
+/*
+ * If you don't want XDMAUTH support (if you don't have Wraphelp.c),
+ * comment this out.
+ *
+ */
+#if defined(LinuxArchitecture)
+#define HasXdmAuth YES
+#endif /* #if defined(LinuxArchitecture) */
+
+/*
+ * If you have Linux DECnet support, and want to build XFree86 with support
+ * for connections over DECnet, uncomment this.
+ *
+#define HasDECnet YES
+ */
+
+/*
+ * To build static and shared libraries with debugging information, uncomment
+ * this. Assumes you have Gcc2.
+ * (If you don't have Gcc2, you can use the DebugLib{X11,Xt,Xaw,...} variables
+ * to build debugging versions of the libraries separately.)
+ *
+#define DebuggableLibraries YES
+*/
+#if defined(LinuxArchitecture)
+#define DebuggableLibraries YES
+#endif /* #if defined(LinuxArchitecture) */
+/*
+ * To forceably build static libraries in addition to shared libraries,
+ * uncomment this.
+ *
+#define ForceNormalLib YES
+ */
+
+/*
+ * Uncomment this if your default tools (eg, gcc, ld, as, etc) are
+ * not the Linux ELF versions.
+ *
+#define LinuxElfDefault NO
+ */
+
+/*
+ * To use ELF format shared libraries for supported OSs, uncomment this.
+ *
+ * For Linux the default setting of this is the same as the setting of
+ * LinuxElfDefault.
+ *
+ * For FreeBSD this should automatically be set correctly by imake. Only
+ * change it here if you need to override the automatic setting.
+ *
+#define UseElfFormat YES
+ */
+
+/*
+ * For FreeBSD/ELF (FreeBSD 3.0) it is possible to also build and install
+ * a.out compatibility libraries. To enable that, uncomment this.
+ *
+#define BuildAoutLibraries YES
+ */
+
+/*
+ * If you have trouble with make bombing out in Xlib, try uncommenting this.
+ * You will not get dependencies as a result, but better than nothing.
+ *
+#define MakeHashTableBug YES
+ */
+
+/*
+ * If you do not want your man pages compress under SVR3 systems that
+ * support it, uncomment this.
+ *
+#define CompressManPages NO
+ */
+
+/*
+ * If you have sgmlfmt (the XFree86 doctools package) and want to build
+ * formatted docs from the SGML source, uncomment this.
+ *
+#define HasSgmlFmt YES
+ */
+
+/*
+ * To disable building some document formats, uncomment some of these.
+ *
+#define BuildLinuxDocText NO
+#define BuildLinuxDocHtml NO
+#define BuildLinuxDocPS NO
+ */
+
+/*
+ * To install Japanese versions of the documentation uncomment this.
+ * Note: The Japanese documentation consists of a subset of the
+ * XFree86 3.1 docs.
+ *
+#define InstallJapaneseDocs YES
+ */
+
+/*
+ * To build/install X specs docs, uncomment the following.
+ * The SpecsDocDirs setting here is recommended because it covers
+ * the docs that XFree86 has changed or added.
+ *
+#define BuildSpecsDocs YES
+#define SpecsDocDirs CTEXT GL ICCCM X11 Xext Xmu Xv XvMC i18n
+ */
+
+/*
+ * To build all specs docs, not just those listed in SpecsDocDirs, uncomment
+ * the following.
+ *
+#define BuildAllSpecsDocs YES
+ */
+
+/*
+ * If your system doesn't support vm86() mode and you have
+ * libx86emu set library path here
+ *
+#define X86EMU_LIBPATH /usr/local/lib
+ */
+
+/*
+ * Most platforms default to using an already installed FreeType 2 library.
+ * To use the one included in this release instead, uncomment the following.
+ *
+#define HasFreetype2 NO
+ */
+#define HasFreetype2 NO
+
+/*
+ * To use a FreeType library already installed outside the default search
+ * paths, uncomment the following and set the path as needed.
+ *
+#define HasFreetype2 YES
+#define Freetype2Dir /usr/local
+ */
+
+
+/*
+ * Most platforms default to using an already installed Fontconfig library.
+ * To use the one included in this release instead, uncomment the following.
+ *
+#define HasFontconfig NO
+ */
+#define HasFontconfig NO
+
+/*
+ * To use a Fontconfig library already installed outside the default search
+ * paths, uncomment the following and set the path as needed.
+#define HasFontconfig YES
+#define FontconfigDir /usr/local
+ */
+
+
+/*
+ * Most platforms default to using an already installed Expat library.
+ * To use the one included in this release instead, uncomment the following.
+ *
+#define HasExpat NO
+ */
+#define HasExpat NO
+
+/*
+ * To use a Expat library already installed outside the default search
+ * paths, uncomment the following and set the path as needed.
+#define HasExpat YES
+#define ExpatDir /usr/local
+ */
+
+
+/*
+ * Most platforms default to using an already installed PNG library.
+ * To use the one included in this release instead, uncomment the following.
+ *
+#define HasLibpng NO
+ */
+
+/*
+ * To use a PNG library already installed outside the default search
+ * paths, uncomment the following and set the path as needed.
+#define HasLibpng YES
+#define LibpngDir /usr/local
+ */
+
+
+/*
+ * Most platforms default to using an already installed xterm program.
+ * To use the one included in this release instead, uncomment the following.
+ *
+#define BuildXterm YES
+ */
+
+#define SharedLibXau NO
+
+#define SharedLibXdmcp NO
+
+#define BuildXaw7 YES
+
+#else /* #if !defined(NXZaurusXServer) && !defined(NXiPAQXServer) && !defined(DarwinArchitecture) */
+
+#if defined(DarwinArchitecture) && !defined(NXZaurusXServer) && !defined(NXiPAQXServer)
+#define NXDarwinServer NO
+#define BuildServersOnly YES
+#define DefaultFontPath /usr/NX/share/fonts/misc/,/usr/NX/share/fonts/TTF/
+#define DefaultRGBDatabase /usr/NX/share/rgb
+#define XprtServer NO
+#define BuildXprint NO
+#define XnestServer NO
+#define XVirtualFramebufferServer NO
+#define BuildFontServer NO
+#define BuildFreeType NO
+#define BuildXTrueType NO
+#define FontLibSharedFreeType NO
+#endif
+
+#if !defined(NXZaurusXServer) && defined(NXiPAQXServer)
+#define KDriveXServer YES
+#define XiPAQH3500Server YES
+#define BuildServersOnly YES
+#define NXEmbeddedXServer YES
+#define KdriveServerExtraDefines -DITSY -DMAXSCREENS=1
+#define TinyXServer YES
+#define CrossCompiling YES
+#define TouchScreen YES
+#define ItsyCompilerBug YES
+#undef BuildRandR
+#define BuildRandR YES
+#define BuildXInputLib YES
+#define BuildXTrueType YES
+#define ServerXdmcpDefines
+#define XipaqServer YES
+#endif
+
+#if !defined(NXiPAQXServer) && defined(NXZaurusXServer)
+#define KDriveXServer YES
+#define XiPAQH3500Server YES
+#define BuildServersOnly YES
+#define ZaurusXServer YES
+#define NXEmbeddedXServer YES
+#define KdriveServerExtraDefines -DITSY -DMAXSCREENS=1
+#define TinyXServer YES
+#define CrossCompiling YES
+#define TouchScreen YES
+#define ItsyCompilerBug YES
+#undef BuildRandR
+#define BuildRandR YES
+#define BuildXInputLib YES
+#define BuildXTrueType YES
+#define ServerXdmcpDefines
+#define XipaqServer YES
+#define XfbdevServer YES
+#endif
+
+#endif /* #if !defined(NXZaurusXServer) && !defined(NXiPAQXServer) && !defined(DarwinArchitecture) */