diff options
Diffstat (limited to 'doc/_attic_/nx-X11_vs_XOrg69_patches/nx-X11_config_cf_host.def.X.original')
| -rw-r--r-- | doc/_attic_/nx-X11_vs_XOrg69_patches/nx-X11_config_cf_host.def.X.original | 1023 |
1 files changed, 1023 insertions, 0 deletions
diff --git a/doc/_attic_/nx-X11_vs_XOrg69_patches/nx-X11_config_cf_host.def.X.original b/doc/_attic_/nx-X11_vs_XOrg69_patches/nx-X11_config_cf_host.def.X.original new file mode 100644 index 000000000..cd1b1fbf6 --- /dev/null +++ b/doc/_attic_/nx-X11_vs_XOrg69_patches/nx-X11_config_cf_host.def.X.original @@ -0,0 +1,1023 @@ +--- ./nx-X11/config/cf/host.def.X.original 2015-02-13 14:03:44.400448260 +0100 ++++ ./nx-X11/config/cf/host.def 2015-02-13 14:03:44.400448260 +0100 +@@ -0,0 +1,1020 @@ ++XCOMM $XFree86: xc/config/cf/xf86site.def,v 3.186 2003/06/25 18:06:22 eich Exp $ ++/******************************************************************************/ ++/* ++ * This file is to provide a quick method for most people to change the ++ * behaviour of their Xorg installation without having to fully ++ * understand the workings of site.def and all the various '.cf' files. ++ * ++ * In the vast majority of cases, it should not be necessary to use this ++ * file at all or change it in any way. ++ * ++ * This file is divided into two sections. The first contains settings ++ * that end-users might reasonably change. The second contains settings ++ * that developers might want to change. ++ * ++ * IMPORTANT NOTE: In all cases changing the defaults may cause problems ++ * and/or unexpected side-effects. If you don't understand what a setting ++ * does, then it's best to not change it. If you make changes and have ++ * problems, verify that those problems are also present when using an ++ * empty host.def file and unchanged version of this file before reporting ++ * them. ++ * ++ * A good way to use this file is to copy it to host.def, and make the ++ * changes there. That way, future patches to this file won't fail. ++ * The host.def file will never be patched. ++ * ++ * The distributed version of this file MUST contain no uncommented ++ * definitions. Default definitions belong in xorg.cf, or <vendor>.cf ++ * files. ++ */ ++/******************************************************************************/ ++ ++/**************************************************************************/ ++/* */ ++/* Copyright (c) 2001, 2011 NoMachine, http://www.nomachine.com/. */ ++/* */ ++/* NX-X11, NX protocol compression and NX extensions to this software */ ++/* are copyright of NoMachine. Redistribution and use of the present */ ++/* software is allowed according to terms specified in the file LICENSE */ ++/* which comes in the source distribution. */ ++/* */ ++/* Check http://www.nomachine.com/licensing.html for applicability. */ ++/* */ ++/* NX and NoMachine are trademarks of Medialogic S.p.A. */ ++/* */ ++/* All rights reserved. */ ++/* */ ++/**************************************************************************/ ++ ++#if !defined(NXZaurusXServer) && !defined(NXiPAQXServer) && !defined(DarwinArchitecture) ++ ++#if defined(SunArchitecture) ++#define ProjectRoot /usr/openwin ++#endif ++ ++/* ++ * Enable use the Cygwin IPC libraries to get MIT-SHM support. ++ */ ++#if defined(cygwinArchitecture) ++#define UseCygIPC YES ++#endif ++ ++/* ++ * If you have build-specific modifications in your host.def file, but ++ * want an empty host.def file installed when doing 'make install', ++ * uncomment the following ++ * ++#define InstallEmptyHostDef ++ */ ++ ++/* ++ * Which servers to build. There is only Xorg server. ++ * It can be disabled by the following. ++ * ++#define XorgServer NO ++ */ ++#define XorgServer NO ++ ++/* ++ * To disable building the Xnest server, uncomment this. ++ * ++#define XnestServer NO ++ */ ++#define XnestServer NO ++ ++/* ++ * To disable building Xvfb, uncomment this. ++ * ++#define XVirtualFramebufferServer NO ++ */ ++#define XVirtualFramebufferServer NO ++ ++/* ++ * To enable building Xdmx, uncomment this. ++ * ++#define XdmxServer YES ++ */ ++#define XdmxServer NO ++ ++/* ++ * To disable building Xprt, uncomment this. ++ * ++#define XprtServer NO ++ */ ++#define XprtServer NO ++ ++/* ++ * Xprint is needed by Xprt. You can disable it if ++ * you are not going to build Xprt. ++ * ++#define BuildXprint NO ++ */ ++#define BuildXprint NO ++ ++/* ++ * Building libraries with NX enhancements is disabled ++ * by default. You should enable this in your host.def. ++ * ++#define NXLibraries YES ++ */ ++#define NXLibraries YES ++ ++/* ++ * Building the NX agent nested server is disabled ++ * by default. Enable this in your host.def. ++ * ++#define NXAgentServer YES ++ */ ++#define NXAgentServer YES ++ ++/* ++ * Assume the new build tree. ++ * ++#define NXUpgradeAgentServer NO ++ */ ++#define NXUpgradeAgentServer YES ++ ++#ifdef NXAgentServer ++#define BuildRenderLibrary YES ++#define SharedLibFreetype2 YES ++#define NormalLibFreetype2 YES ++#define FontLibSharedFreeType NO ++#endif ++ ++/* ++ * Define this symbol to build the NX enhanced MS Windows ++ * X server for Cygnus environment. ++ * ++#define NXWinServer YES ++ */ ++#if defined(cygwinArchitecture) ++#define NXWinServer NO ++#define XWinServer NO ++#endif ++ ++/* ++ * Set the default server (ie the one that gets the sym-link to "X") ++ * ++#define ServerToInstall Xorg ++ */ ++ ++/* ++ * Force build of X libraries if any nested server is to be built. ++ * ++#define BuildLibraries YES ++ * ++ * If you just want libraries for NXAgentServer, this should be ++ * enough (never tested, although). ++ * ++#define BuildLibrariesForXServers YES ++ */ ++#if XnestServer || NXAgentServer ++#define BuildLibraries YES ++#endif ++ ++#define BuildDamageLibrary YES ++ ++#define BuildXfixesLibrary YES ++ ++#define BuildCompositeLibrary YES ++ ++#define BuildRandRLibrary YES ++ ++#define BuildDocs NO ++ ++#define BuildComposite YES ++ ++/* ++ * If you only run the X server under xdm the X servers don't need to be ++ * installed SetUID, and you may comment out the lines below. If you run ++ * the servers by hand (with xinit or startx), then they do need to be ++ * installed SetUID on most platforms. ++ * ++ * Consult your system administrator before making the X server setuid. ++ * ++#define InstallXserverSetUID NO ++ */ ++ ++ ++/* ++ * Server configuration parameters. The defaults are shown here: ++ */ ++ ++/* ++ * Which drivers to build. When building a static server, each of these ++ * will be included in it. When building the loadable server each of these ++ * modules will be built. ++ * ++#define XF86CardDrivers mga glint nv tga s3virge sis rendition \ ++ neomagic i740 tdfx savage \ ++ cirrus vmware tseng trident chips apm \ ++ GlideDriver fbdev i128 \ ++ ati DevelDrivers ark cyrix \ ++ siliconmotion \ ++ vesa vga XF86OSCardDrivers XF86ExtraCardDrivers ++ */ ++ ++/* ++ * To add third party drivers to the standard driver list, set the ++ * following. ++ * ++#define XF86ExtraCardDrivers extradriver1 extradriver2 ... ++ */ ++ ++/* ++ * Select the XInput devices you want by uncommenting this. ++ * ++#define XInputDrivers mouse keyboard acecad calcomp citron \ ++ digitaledge dmc dynapro elographics \ ++ microtouch mutouch penmount spaceorb summa \ ++ wacom void magictouch aiptek ++ */ ++ ++/* To enable building of development DRI drivers (insecure, or not ++ * useful on the chosen architecture, uncomment this define. ++#define BuildDevelDRIDrivers YES ++ */ ++ ++/* ++ * To use the deprecated, old keyboard driver, uncomment this. But ++ * even better, make the new keyboard driver (hw/xfree86/input/keyboard) ++ * work for your architechture. The old driver will be removed in the ++ * next release. ++ * ++#define UseDeprecatedKeyboardDriver YES ++ */ ++ ++/* ++ * There are three parameters that determine where and how the Matrox HAL ++ * library is used: ++ * ++ * HaveMatroxHal -- You have the HALlib.a binary library installed ++ * in xfree86/drivers/mga/HALlib, and you want it to ++ * be used. ++ * Default: NO ++ * ++ * BuildMatroxHal -- You have the source for the HALlib library (installed ++ * in xfree86/drivers/mga/hallib), and want to build and ++ * use it. ++ * Default: NO ++ * ++ * UseMatroxHal -- You want to build support for loading/using the HAL ++ * library into the mga driver. For module server builds ++ * you don't need to have the HALlib library to do this. ++ * but you want to build support for loading it and using ++ * it into the mga driver module. ++ * Default: YES for loadable server build ++ * (HaveMatroxHal || BuildMatroxHal) for static ++ */ ++ ++/* ++ * To disable use of the Matrox HAL library, uncomment this: ++ * ++#define UseMatroxHal NO ++ */ ++ ++/* ++ * If you have the HALlib.a binary installed in xfree86/drivers/mga/HALlib, ++ * uncomment this: ++ * ++#define HaveMatroxHal YES ++ */ ++ ++/* ++ * If you have the HALlib source code installed in xfree86/drivers/mga/hallib, ++ * uncomment this: ++#define BuildMatroxHal YES ++ */ ++ ++/* ++ * To disable building the font server, uncomment this. ++ * ++#define BuildFontServer NO ++ */ ++#define BuildFontServer NO ++ ++/* ++ * Speedo fonts have been disabled by default in this release. ++ * To re-enable support for Speedo fonts, uncomment this. ++ * ++#define BuildSpeedo YES ++ */ ++ ++/* ++ * To disable support for CID fonts, uncomment this. ++ * ++#define BuildCID NO ++ */ ++ ++/* ++ * To disable support for TrueType fonts, uncomment these. ++ * ++#define BuildFreeType NO ++ */ ++ ++/* ++ * To set non-default build options for the underlying FreeType libraries, ++ * add them here and uncomment. ++ * ++#define Freetype2BuildDefines -DFREETYPE_BUILD_DEFINES ++ */ ++ ++/* ++ * To build the FreeType libraries with the TrueType byte code interpreter ++ * enabled, uncomment this. Note that there are patent issues related to the ++ * TrueType byte code interpreter, and we only recommend you enabling this ++ * if you are sure that there are no legal impediments to you doing so. See ++ * <http://www.freetype.org/patents.html> for further information. ++ * ++#define Freetype2BuildDefines -DTT_CONFIG_OPTION_BYTECODE_INTERPRETER ++ */ ++ ++/* ++ * Do you want to Build Fonts (Usually you only want to build and install ++ * fonts once, if this is a first time install you will want to build the ++ * fonts) ++ * ++#define BuildFonts NO ++ */ ++#define BuildFonts NO ++ ++/* ++ * To not build/install the 75dpi fonts, uncomment the following ++ * ++#define Build75DpiFonts NO ++ */ ++ ++/* ++ * To not build/install the 100dpi fonts, uncomment the following ++ * ++#define Build100DpiFonts NO ++ */ ++ ++/* ++ * To build/install the Speedo fonts, uncomment the following ++ * (see setting above about Speedo support as well) ++ * ++#define BuildSpeedoFonts YES ++ */ ++ ++/* ++ * To not build/install the Type1 fonts, uncomment the following ++ * ++#define BuildType1Fonts NO ++ */ ++ ++/* ++ * To not build/install the CID fonts, uncomment the following ++ * ++#define BuildCIDFonts NO ++ */ ++ ++/* ++ * To not build/install the True Type fonts, uncomment the following ++ * ++#define BuildTrueTypeFonts NO ++ */ ++ ++/* ++ * To not build/install the Cyrillic fonts, uncomment the following ++ * ++#define BuildCyrillicFonts NO ++ */ ++ ++/* ++ * To not install the local font directory, uncomment the following ++ * ++#define MakeLocalFontDir NO ++ */ ++ ++/* ++ * Include True Type Fonts to default font path. It is safe to do ++ * this by default as NX intaller carries only misc and TTF in the ++ * basic set of fonts installed under Windows. ++ * ++#define DefaultFontPath $(FONTDIR)/misc/,$(FONTDIR)/Speedo/,$(FONTDIR)/Type1/,$(FONTDIR)/75dpi/,$(FONTDIR)/100dpi/ ++ */ ++ ++#if defined(LinuxArchitecture) || defined(SunArchitecture) || defined(FreeBSDArchitecture) ++#define DefaultFontPath $(FONTDIR)/misc/,$(FONTDIR)/Speedo/,$(FONTDIR)/Type1/,$(FONTDIR)/75dpi/,$(FONTDIR)/100dpi/,$(FONTDIR)/TTF/ ++#endif /* #if defined(LinuxArchitecture) || defined(SunArchitecture) */ ++ ++#if defined(cygwinArchitecture) ++#define DefaultFontPath /mnt/NX/fonts/base/,/mnt/NX/fonts/misc/,/mnt/NX/fonts/Speedo/,/mnt/NX/fonts/Type1/,/mnt/NX/fonts/75dpi/,/mnt/NX/fonts/100dpi/,/mnt/NX/fonts/TTF/ ++#define DefaultRGBDatabase /mnt/NX/fonts/rgb ++#endif /* #if defined(cygwinArchitecture) */ ++ ++/* ++ * To build only the servers with a cut-down source tree, uncomment ++ * this. ++ * ++#define BuildServersOnly YES ++ */ ++#define BuildServersOnly YES ++ ++/* ++ * By default, the sample config files for xinit, xdm and xfs are installed ++ * only when there is no pre-existing version installed. Uncommenting the ++ * following lines will force the sample versions to be installed even if ++ * it means over-writing existing versions. ++ * ++#define InstallXinitConfig YES ++#define InstallXdmConfig YES ++#define InstallFSConfig YES ++ */ ++ ++/* ++ * By default the application defaults files are always installed. ++ * Uncommenting the the following will prevent exising application ++ * defaults files from being over-written. ++ * ++#define InstallAppDefFiles NO ++ */ ++ ++/* ++ * Undefine the following if you don't want to have config files and ++ * app-defaults installed in a separate directory (i.e. /etc/X11). ++ * ++#define UseSeparateConfDir NO ++ */ ++ ++/* ++ * To enable building the glide driver, you need to define ++ * HasGlide2 to YES and set the Glide2IncDir variable. ++ * HasGlide2 is per default NO. ++ * ++#define HasGlide2 YES ++ */ ++ ++/* ++ * Set the path to your Glide include files. ++ * ++#define Glide2IncDir /usr/include/glide ++ */ ++ ++/* ++ * Have glide 3? ++ * ++#define HasGlide3 YES ++ */ ++ ++/* ++ * Set the path to your Glide 3 include files. ++ * ++#define Glide3IncDir /usr/include/glide3 ++ */ ++ ++ ++ ++/* ++ * Unless you're a developer you shouldn't need to change anything ++ * beyond this point. ++ */ ++ ++/* ++ * If you want to enable some developer settings, like more verbose ++ * compiler warnings, uncomment this. ++ * ++#define XFree86Devel YES ++*/ ++ ++/* ++ * If using GCC 2.x on a system where it isn't the default, uncomment ++ * the following ++ * ++ */ ++#if defined(SunArchitecture) ++#define HasGcc2 YES ++#define HasGcc YES ++#endif ++ ++/* ++ * The default optimisation flags for GCC 2.x. -fno-strength-reduce is ++ * here to work around a bug in -O2 for GCC 2.x on i386 platforms. ++ * If you are using a version that doesn't have this bug, you can ++ * uncomment the following line, and remove '-fno-strength-reduce' ++ * If you are building binaries for a 486, it may be beneficial to add ++ * -m486 ++ * ++#define DefaultGcc2i386Opt -O2 -fno-strength-reduce ++ */ ++ ++#if defined (LinuxArchitecture) ++#define DefaultGcc2i386Opt -g -O3 ++#endif ++ ++/* ++ * Enable all the optimizations on AMD64. ++ */ ++ ++#define DefaultGcc2AMD64Opt -g -O3 GccAliasingArgs ++ ++/* ++ * This allows the GCC warning flags to be set. The default is shown here. ++ * ++#define GccWarningOptions -Wall -Wpointer-arith -Wstrict-prototypes \ ++ -Wmissing-prototypes -Wmissing-declarations \ ++ -Wredundant-decls -Wnested-externs ++ */ ++ ++/* ++ * Sun Compiler stuff.. ++ * ++#define HasSunC YES ++#define HasSunCplusplus YES ++#define CplusplusCompilerMajorVersion 5 ++#define CplusplusCompilerMinorVersion 0 ++#define CCompilerMajorVersion 5 ++#define CCompilerMinorVersion 0 ++ */ ++ ++/* ++ * Optimized Sun Compiler Build. ++ * ++#define DefaultCDebugFlags -xO4 -xtarget=pentium_pro ++#define OptimizedCDebugFlags -xO4 -xtarget=pentium_pro ++ */ ++ ++/* ++ * Debuggable Sun Compiler Build. ++ * Note: This builds _EVERYTHING_ as debuggable ++ * ++#define DefaultCDebugFlags -g -xs ++#define OptimizedCDebugFlags -g -xs ++ */ ++ ++/* ++ * For Linux, this should match the Binutils version you have. This example ++ * is for 2.6.0.7. See linux.cf for the default setting. ++ * ++ * This should automatically get set correctly by imake. ++ * ++#define LinuxBinUtilsMajorVersion 26 ++ */ ++ ++/* ++ * For Linux, these should match the libc version you have. This example ++ * is for libc.5.4.x. See linux.cf for the default setting. ++ * ++ * This should automatically get set correctly by imake. ++ * ++#define LinuxCLibMajorVersion 5 ++#define LinuxClibMinorVersion 4 ++ */ ++ ++/* ++ * If you want to use the GNU malloc library, uncomment this ++ * ++#define UseGnuMalloc YES ++ */ ++ ++/* ++ * Set this to whatever is required to access the GNU malloc library. ++ * The default is '-lgmalloc' unless is specified in the OS's .cf file. ++ * ++#define GnuMallocLibrary -L/usr/local/lib -lgmalloc ++ */ ++ ++/* ++ * To enable the internal Xserver malloc, uncomment this ++ * ++#define UseInternalMalloc YES ++ */ ++ ++/* ++ * Some Linux releases don't have a libtermcap. In this case you may need ++ * to uncomment the following ++ * ++#define TermcapLibrary -lncurses ++ */ ++ ++/* ++ * Build a server that dynamically loads the modules by setting ++ * this to YES. This defaults to YES on most platforms. A static server ++ * can be built by setting this to NO. ++ * ++#define DoLoadableServer NO ++ */ ++ ++/* ++ * This release defaults to building dlopen() style modules instead of the ++ * previously standard loader modules. ++ * ++ * Uncomment the following to return to the XFree86 custom loader modules. ++ * ++#define MakeDllModules NO ++ */ ++ ++/* ++ * Build XAA. This can be disabled with: ++ * ++#define XF86XAA NO ++ */ ++ ++/* ++ * Build vgahw. This can be disabled with: ++ * ++#define XF86VgaHw NO ++ */ ++ ++/* ++ * Build xf1bpp. This can be disabled with: ++ * ++#define XF1Bpp NO ++ */ ++ ++/* ++ * Build xf4bpp. This can be disabled with: ++ * ++#define XF4Bpp NO ++ */ ++ ++ ++/* ++ * BSD Console driver support (for FreeBSD and NetBSD). ++ * ++ * By default, support is included for pccons and pcvt for NetBSD, and ++ * pccons, syscons and pcvt for FreeBSD. ++ * ++ * To change the list of supported drivers, set the following parameter. ++ * Possible values are -DPCCONS_SUPPORT, -DSYSCONS_SUPPORT, -DPCVT_SUPPORT. ++ * The following example includes support for syscons and pcvt only. ++ * ++#define XFree86ConsoleDefines -DSYSCONS_SUPPORT -DPCVT_SUPPORT ++ */ ++ ++/* ++ * To link the X server with a dynamic version of the Xfont library, ++ * uncomment this. ++ * ++#define XserverStaticFontLib NO ++ */ ++ ++/* ++ * To enable binary compatibility with previous versions of the font ++ * encoding support, uncomment this. ++ * ++#define FontencCompatibility YES ++ */ ++ ++/* ++ * To disable building XInput support, uncomment this ++ * ++#define BuildXInputExt NO ++ */ ++#if defined(SunArchitecture) ++#define BuildXInputExt YES ++#endif ++ ++/* ++ * Uncomment this for joystick support. ++ * ++ * Note: Joystick support is broken, so don't enable this. ++ * ++#define JoystickSupport YES ++ */ ++ ++/* ++ * To disable the ScreenSaver Extension, uncomment this line. ++ * ++#define BuildScreenSaverExt NO ++ */ ++#define BuildScreenSaverExt NO ++ ++/* ++ * If you don't want to build Xinerama support, uncomment this. ++ * ++#define BuildXinerama NO ++ */ ++#define BuildXinerama NO ++ ++/* ++ * If you don't want to build support for the GLX extension, uncomment this. ++ * ++#define BuildGlxExt NO ++ */ ++#define BuildGlxExt YES ++ ++/* ++ * Taken from xorg.cf. ++ */ ++ ++#if defined(SparcArchitecture) \ ++ || defined (Sparc64Architecture) \ ++ || defined(ia64Architecture) \ ++ || defined(s390xArchitecture) \ ++ || defined(AMD64Architecture) ++#define GlxExtraDefines -D__GLX_ALIGN64 ++#endif ++ ++/* ++ * If you want to build the xf86rush extension, uncomment this line. ++ * This isn't recommended. ++ * ++#define BuildXF86RushExt YES ++ */ ++#define BuildXF86RushExt NO ++ ++/* ++ * If you want to build the client library for the xf86rush extension, ++ * uncomment this line. This isn't recommended. ++ * ++#define BuildXF86RushLibrary NO ++ */ ++#define BuildXF86RushLibrary NO ++ ++/* ++ * We should never need LBX in a NX enabled environment... ++ * ++#define BuildLBX NO ++ */ ++#define BuildLBX NO ++ ++#define BuildXKB YES ++#define BuildXKBlib YES ++ ++#define SharedLibXau NO ++ ++/* ++ * If you are running NetBSD 0.9C or later, and have the aperture driver ++ * installed, uncomment this. ++ * ++#define HasNetBSDApertureDriver YES ++ */ ++ ++/* ++ * If you are running SVR3 and have the mmap driver installed (for linear ++ * framebuffer access) uncomment this. ++ * ++#define HasSVR3mmapDrv YES ++ */ ++ ++/* ++ * If you are using an SVR3 (like ISC 4.x) which supports long file names, ++ * you can uncomment this to have manual pages installed under their ++ * full names ++ * ++#define ExpandManNames YES ++ */ ++ ++/* ++ * For a POSIXized build on Interactive uncomment this ++ * Could be used with gcc 'till Version 2.6.3 ++ * Should be used with gcc 2.7.2. ++ * ++#define UsePosix YES ++ */ ++ ++/* ++ * If you don't want XDMAUTH support (if you don't have Wraphelp.c), ++ * comment this out. ++ * ++ */ ++#if defined(LinuxArchitecture) ++#define HasXdmAuth YES ++#endif /* #if defined(LinuxArchitecture) */ ++ ++/* ++ * If you have Linux DECnet support, and want to build XFree86 with support ++ * for connections over DECnet, uncomment this. ++ * ++#define HasDECnet YES ++ */ ++ ++/* ++ * To build static and shared libraries with debugging information, uncomment ++ * this. Assumes you have Gcc2. ++ * (If you don't have Gcc2, you can use the DebugLib{X11,...} variables ++ * to build debugging versions of the libraries separately.) ++ * ++#define DebuggableLibraries YES ++*/ ++#if defined(LinuxArchitecture) ++#define DebuggableLibraries YES ++#endif /* #if defined(LinuxArchitecture) */ ++/* ++ * To forceably build static libraries in addition to shared libraries, ++ * uncomment this. ++ * ++#define ForceNormalLib YES ++ */ ++ ++/* ++ * Uncomment this if your default tools (eg, gcc, ld, as, etc) are ++ * not the Linux ELF versions. ++ * ++#define LinuxElfDefault NO ++ */ ++ ++/* ++ * To use ELF format shared libraries for supported OSs, uncomment this. ++ * ++ * For Linux the default setting of this is the same as the setting of ++ * LinuxElfDefault. ++ * ++ * For FreeBSD this should automatically be set correctly by imake. Only ++ * change it here if you need to override the automatic setting. ++ * ++#define UseElfFormat YES ++ */ ++ ++/* ++ * For FreeBSD/ELF (FreeBSD 3.0) it is possible to also build and install ++ * a.out compatibility libraries. To enable that, uncomment this. ++ * ++#define BuildAoutLibraries YES ++ */ ++ ++/* ++ * If you have trouble with make bombing out in Xlib, try uncommenting this. ++ * You will not get dependencies as a result, but better than nothing. ++ * ++#define MakeHashTableBug YES ++ */ ++ ++/* ++ * If you do not want your man pages compress under SVR3 systems that ++ * support it, uncomment this. ++ * ++#define CompressManPages NO ++ */ ++ ++/* ++ * If you have sgmlfmt (the XFree86 doctools package) and want to build ++ * formatted docs from the SGML source, uncomment this. ++ * ++#define HasSgmlFmt YES ++ */ ++ ++/* ++ * To disable building some document formats, uncomment some of these. ++ * ++#define BuildLinuxDocText NO ++#define BuildLinuxDocHtml NO ++#define BuildLinuxDocPS NO ++ */ ++ ++/* ++ * To install Japanese versions of the documentation uncomment this. ++ * Note: The Japanese documentation consists of a subset of the ++ * XFree86 3.1 docs. ++ * ++#define InstallJapaneseDocs YES ++ */ ++ ++/* ++ * To build/install X specs docs, uncomment the following. ++ * The SpecsDocDirs setting here is recommended because it covers ++ * the docs that XFree86 has changed or added. ++ * ++#define BuildSpecsDocs YES ++#define SpecsDocDirs CTEXT GL ICCCM X11 Xext Xmu Xv XvMC i18n ++ */ ++ ++/* ++ * To build all specs docs, not just those listed in SpecsDocDirs, uncomment ++ * the following. ++ * ++#define BuildAllSpecsDocs YES ++ */ ++ ++/* ++ * If your system doesn't support vm86() mode and you have ++ * libx86emu set library path here ++ * ++#define X86EMU_LIBPATH /usr/local/lib ++ */ ++ ++/* ++ * Most platforms default to using an already installed FreeType 2 library. ++ * To use the one included in this release instead, uncomment the following. ++ * ++#define HasFreetype2 NO ++ */ ++#define HasFreetype2 NO ++ ++/* ++ * To use a FreeType library already installed outside the default search ++ * paths, uncomment the following and set the path as needed. ++ * ++#define HasFreetype2 YES ++#define Freetype2Dir /usr/local ++ */ ++ ++ ++/* ++ * Most platforms default to using an already installed Fontconfig library. ++ * To use the one included in this release instead, uncomment the following. ++ * ++#define HasFontconfig NO ++ */ ++#define HasFontconfig NO ++ ++/* ++ * To use a Fontconfig library already installed outside the default search ++ * paths, uncomment the following and set the path as needed. ++#define HasFontconfig YES ++#define FontconfigDir /usr/local ++ */ ++ ++ ++/* ++ * Most platforms default to using an already installed Expat library. ++ * To use the one included in this release instead, uncomment the following. ++ * ++#define HasExpat NO ++ */ ++#define HasExpat NO ++ ++/* ++ * To use a Expat library already installed outside the default search ++ * paths, uncomment the following and set the path as needed. ++#define HasExpat YES ++#define ExpatDir /usr/local ++ */ ++ ++ ++/* ++ * Most platforms default to using an already installed PNG library. ++ * To use the one included in this release instead, uncomment the following. ++ * ++#define HasLibpng NO ++ */ ++ ++/* ++ * To use a PNG library already installed outside the default search ++ * paths, uncomment the following and set the path as needed. ++#define HasLibpng YES ++#define LibpngDir /usr/local ++ */ ++ ++ ++/* ++ * Most platforms default to using an already installed xterm program. ++ * To use the one included in this release instead, uncomment the following. ++ * ++#define BuildXterm YES ++ */ ++ ++#define SharedLibXau NO ++ ++#define SharedLibXdmcp NO ++ ++#define BuildXaw7 YES ++ ++#else /* #if !defined(NXZaurusXServer) && !defined(NXiPAQXServer) && !defined(DarwinArchitecture) */ ++ ++#if defined(DarwinArchitecture) && !defined(NXZaurusXServer) && !defined(NXiPAQXServer) ++#define NXDarwinServer NO ++#define BuildServersOnly YES ++#define DefaultFontPath /usr/NX/share/fonts/misc/,/usr/NX/share/fonts/TTF/ ++#define DefaultRGBDatabase /usr/NX/share/rgb ++#define XprtServer NO ++#define BuildXprint NO ++#define XnestServer NO ++#define XVirtualFramebufferServer NO ++#define BuildFontServer NO ++#define BuildFreeType NO ++#define BuildXTrueType NO ++#define FontLibSharedFreeType NO ++#endif ++ ++#if !defined(NXZaurusXServer) && defined(NXiPAQXServer) ++#define KDriveXServer YES ++#define XiPAQH3500Server YES ++#define BuildServersOnly YES ++#define NXEmbeddedXServer YES ++#define KdriveServerExtraDefines -DITSY -DMAXSCREENS=1 ++#define TinyXServer YES ++#define CrossCompiling YES ++#define TouchScreen YES ++#define ItsyCompilerBug YES ++#undef BuildRandR ++#define BuildRandR YES ++#define BuildXInputLib YES ++#define BuildXTrueType YES ++#define ServerXdmcpDefines ++#define XipaqServer YES ++#endif ++ ++#if !defined(NXiPAQXServer) && defined(NXZaurusXServer) ++#define KDriveXServer YES ++#define XiPAQH3500Server YES ++#define BuildServersOnly YES ++#define ZaurusXServer YES ++#define NXEmbeddedXServer YES ++#define KdriveServerExtraDefines -DITSY -DMAXSCREENS=1 ++#define TinyXServer YES ++#define CrossCompiling YES ++#define TouchScreen YES ++#define ItsyCompilerBug YES ++#undef BuildRandR ++#define BuildRandR YES ++#define BuildXInputLib YES ++#define BuildXTrueType YES ++#define ServerXdmcpDefines ++#define XipaqServer YES ++#define XfbdevServer YES ++#endif ++ ++#endif /* #if !defined(NXZaurusXServer) && !defined(NXiPAQXServer) && !defined(DarwinArchitecture) */ |